our main products contains: Stainless steel spherical bearing housing、Engineering plastics bearing housing、Zinc alloy bearing housing、punching bearing housing、iron casting bearing housing and so on.

news center

新闻中心
your current location:home>he use and installation position of the bearing seat

News Recommended

The company's website is open, welcome ne

The companys website is open, welcome new and old customers to visit this station

Common fault of rolling bearing

Common fault of rolling bearing The failure of rolling bearing generally shows tw

he basic situation of the products produc

Warmly congratulate Changzhou Shi Hui transmission Co., Ltd. in the 0 month of 20

he use and installation position of the b

: vertical bearing: P200 series (P203-P220), P300 series (P305-P328) of this type

Contact Us

Contact: Manager Wang
Mobile phone: 13961432521
Tel: 0519-85853682
Fax: 0519-85853682
Manager Zhu: 13813676349
Email: yhy2521@163.com

he use and installation position of the bearing seat
  

: vertical bearing: P200 series (P203-P220), P300 series (P305-P328) of this type of product is equipped with 2 series 3 series bearings, bearings, tie a spherical ball bearing the most typical a type most commonly used, suitable for all the drive devices and the shaft and the mounting machine is parallel to the surface of the. When used, it has sufficient strength and steel.
2: square flange seat: F200 series (F203-F220) and F300 series (F305-F328). This type of product is equipped with 2 series bearings and 3 series bearings. It is generally installed on the side wall of the machine, with simple structure and convenient installation. It is suitable for occasions with heavy load. It is one of the most widely used flanged bearing seats.
3: Diamond flange seat: FL200 series (F203-F28) and FL300 series (FL305-FL35). This type of product is equipped with 2 series bearings and 3 series bearings. The structure is light and convenient to install, so it is suitable for installation in smaller transmission parts. The two screw hole center distance is consistent with the same type of square block diagonal bolt hole center distance. So it can replace the square seat.
4: narrow vertical seat: PA200 series (PA203-PA23) and PA300 series (PA305-PA33). This type of product is equipped with 2 series bearings and 3 series bearings. There are two mounting screws holes at the bottom, the width is greatly compressed, which is suitable for the limited installation area.
5: high central vertical seat: PH200 series (PH203-PH23). This type of product is equipped with 2 series bearings, the usage and usage are identical with UCP200, and the difference between the axis center height is higher than the ordinary vertical seat.
6: suspension type seat: HA200 series (HA203-HA23). This type of product is equipped with 2 series bearings, one end of the bearing seat is equipped with adjusting screw holes, and the bearing seat can be connected to the screw to adjust the installation position, which is generally used in occasions where the load is small.
7: adjustable rhombus seat: FA200 series (FA203-FA23) this type of product with 2 series bearings, a diamond shaped seat of the deformation. One of the bolts is changed to an arc groove located at the center of another hole. Therefore, the axis position can be adjusted in a certain range.
8: three hole flange diamond block: FB200 series (FB203-FB23) of this type of product is equipped with 2 series of bearings, a deformation diamond seat, three installation bolt hole on one side of the seat to. It is suitable for the vertical position of the installation surface, which can be used instead of the vertical seat.
9: convex round flange seat: FC200 series (FC203-FC220). This type of product is equipped with 2 series bearings, a circular flange bearing seat and a circular convex table on the bottom, which can be placed in the round hole of the rack, so the installation accuracy is high and the location is accurate.
0: convex square bearing block: FS300 series (FS305-FS328). This type of product is equipped with 3 series bearings, a square flange bearing seat and a circular convex table on the bottom, which can be placed in the round hole of the rack, so the installation accuracy is high and the location is accurate.
: slide block: T200 series (T203-T220), T300 series (T305-T328), K200 series (K203-K22). This type of product is equipped with 2 series bearings, 3 series bearings, two sliding chutes on the top and bottom. It can move back and forth on the rack. Therefore, it is most suitable for the occasion where the inter axial distance is adjusted. The axis of the machine can also be moved in operation. It is mostly used on the belt, chain and other transmission shaft.
2: ring seat: C200 series (C203-C28), C300 series (C305-C328); this type of product is equipped with 2 series 3 series bearings, bearings, the external diameter of bearing seat, can be embedded in the frame of the pre lined hole, can bear large radial load, is used for the machine on the heavy frame.
Outer spherical plate stampede model:
: stamping vertical seat: PP200 series and 2 series bearings are made up of upper and lower shells made of steel plate. It has lighter weight and smaller volume than iron castings. It is the smallest seat type installed in vertical base. But it can only be applied to small loads.
2: stamping round seat CY200 series with 2 series of bearings, can form a circular shell stamping consists of two interchangeable, made of high quality sheet erosion, its function with the same kind of cast iron is similar, because the stamping seat design is lightweight, compact structure, small space for installation, the load is smaller, speed is not high Yang He applications is the ideal.
3: stamping diamond block CL200 series with 2 series of bearings, the punching seat has more installation space is good, it is appearance with spherical bearing in the smallest, lightest seat type.

You may also be interested in this

Related Reading